Forward Controls Design OPF-G-RMR

$68.00

OPF-G, RMR (Optics Platform, Glock, for RMR) is a Glock MOS Adapter Set 01 and Set 02 compatible plate for mounting Trijicon RMR or SRO on Glock Gen 4 and Gen 5 slides, G17, G19, G34, G35, G41 (width 25mm/1 inch.) and G40 that uses Set 02.  Glock’s OEM MOS plate’s width matches that of the slide, but OPF-G, RMR is already wider to fully support the RMR, thus it is compatible with all MOS equipped Glock slides.

7 in stock (can be backordered)

unlimited available through backorder
SKU: OPF-G-RMR Categories: , , , ,
Description

Description

NOTE:

OPF-G, RMR is designed for Trijicon RMR and SRO.  If you use a Holosun and the long set of screws with OPF-G, RMR, you will risk damaging the plate.  We do not support any Holosun sights for use with OPF-G, RMR,
 
Trijicon’s tolerance between the recoil lugs to the front radiused edge of the RMR is +/- 0.005.  While every OPF-G, RMR has been tested on our RMR and SRO, there is always a chance it might not fit your RMR/SRO without fitting.  OPF-G, RMR’s design cradles the sight tightly on the plate between the plate’s front and rear fences,  some fitting may be required.  A competent gunsmith can do it easily if you’re uncomfortable with fitting the plate to your sight.

 

OPF-G, RMR (Optics Platform, Glock, for RMR) is a Glock MOS Adapter Set 01 and Set 02 compatible plate for mounting Trijicon RMR or SRO on Glock Gen 4 and Gen 5 slides, G17, G19, G34, G35, G41 (width 25mm/1 inch.) and G40 that uses Set 02.  Glock’s OEM MOS plate’s width matches that of the slide, but OPF-G, RMR is already wider to fully support the RMR, thus it is compatible with all MOS equipped Glock slides.
We like the Glock MOS concept, even if we find the factory MOS adapter plates could use some help.  Standards, commonality, availability of parts are all good things.  Heretofore, users have had to send in their slides to be milled to accept mini red dot sights, or opt for 3rd party optics ready slides.  The time it takes to send in the slides to be milled, and varying quality of the milling work and optics ready slides notwithstanding, there was a lack a standard regarding the sight height, it’d be a coincidence if two slides milled by two different shops share the same sight height.   Glock’s MOS may not sit as low as some, but in our opinion, what MOS offers more than makes up for it, namely a uniform sight height, ease of installation, parts commonality and availability.
OPF-G, RMR is a collaboration with a USMC combat veteran and former USMC Shooting Team head coach, Tom Shields. We used Glock’s MOS adapter plates as a basis, and designed our version of what we think it should and can be.
OPF-G, RMR’s shape follows its functions, same as all of our products.  We outlined the following objectives:
1. Sight is to be fully supported in the front and rear by recoil lugs/fences, with minimum movement.
2. Eliminate the need to use an additional sealer plate.
3. Correct length sight to plate, and plate to slide screws.  Screws are to be Torx.
4. Adapter plate is to be machined in steel.
OPF-G, RMR accomplishes all of the goals outlined above.  Machined in 1018 steel, and black nitrided,  OPF-G, RMR’s thickness is unchanged from that of the Glock MOS plate, it doesn’t change the sight’s mounted height, nor does it require different iron sights.
OPF-RMR is shipped with plate to slide screws (M3-0.5mm x 6mm, same as what Glock MOS plates uses), and sight to plate screws (6/32 x 3/8), a T10 key and a VC3 packet.
Weight: 0.83oz
Plate to slide torque value: 13 to 15in/lb
Sight to plate torque value: 13in/lb
Proudly designed and made in the USA.
 
OPF-G,RMR supports the full width of the RMR and SRO, a sealer plate is not necessary.  Trijicon’s position is that if the user is unsure, use the sealer plate, and the plate is so thin, if it is used it doesn’t make any difference to the thread engagement.  Trijicon’s guide line on whether a sealer plate is required: https://www.trijicon.com/frequently-asked-questions/category/rmr-faqs
 

OPF-G, RMR is designed to sandwich the sight in its front and rear fence, we make the spacing as close to Trijicon’s dimensions and tolerance as we can.  Though we hold a 0.003 tolerance, Trijicon’s tolerance is 0.005.  In practical terms, this means while some RMRs will move inside the fences by a very small amount, others will need to be forced into the space. 
 
Vibra-tite VC-3 is included with OPF-G, RMR.  Instructions can be found here: https://www.vibra-tite.com/wp-content/uploads/213_tds.pdf
Vibra-tite also provides a video on the application of VC-3: https://www.vibra-tite.com/portfolio-items/vc-3-threadmate-overview-video/
 
A T10 key is provided.  A proper torque wrench in inch/lb increments is required to impart the correct torque to the plate to slide, and sight to plate screws. 
 
For good printable 8×11″  RMR targets (1MOA dot, 2MOA dot, 6.5MOA dot at 100 yard, 50 yard, 25 yard, and 15 yard), please follow this link: https://www.barelytactical.org/targets/
 
HOLOSUN COMPATIBILITY:
Trjicon RMR and SRO share the same mounting footprint, OPF-G, RMR is also compatible with SRO.   However, due to the precise fit of the front and rear recoil lugs/fences that are designed to closely sandwich the sight, OPF-G, RMR is not guaranteed to work with all Holosun sights.
To view our other Forward Controls offerings please follow the link below. Thank you for your support!
Additional information

Additional information

Weight 0.4 lbs
Dimensions 6 × 5 × 1 in
upc

Brand

Forward Controls Design

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “Forward Controls Design OPF-G-RMR”

Your email address will not be published. Required fields are marked *

Shipping & Delivery

All shipping is calculated at checkout. You can choose between USPS and UPS for your shipping needs. All orders can be shipped at various speeds.

All ammo must ship via UPS